Wavetech Telecom

An RF antenna, or radio frequency antenna, is a device that is designed to transmit or receive electromagnetic waves in the radio frequency (RF) spectrum. RF antennas are commonly used in telecommunications systems to transmit and receive radio signals over long distances. RF antennas are used in a variety of telecommunications systems, including cell phone networks, radio and television broadcasting, satellite communication systems, and wireless networking systems. They play a critical role in enabling the transmission and reception of data, voice, and other types of information over long distances.

An RF (Radio Frequency) connector is an electrical connector designed to work with signals in the multi-megahertz range, typically used in radio communication systems. RF connectors are used to connect various components in radio equipment, such as antennas, transmitters, receivers, and amplifiers. RF connectors typically have a threaded or snap-on interface that provides a secure and stable connection. They are often made of metal, such as brass or stainless steel, to provide good electrical conductivity and durability. RF connectors are widely used in the telecommunications, broadcasting, military, and aerospace industries, as well as in scientific research and medical equipment.

RF filters are electronic components that are used to allow or prevent selected signals or frequencies in order to eliminate noise or pass-through of unwanted signals. Common types are low-pass filters, high-pass filters, and bandpass filters. In a radiofrequency/microwave system, it's common to have to distinguish useful frequency signals from worthless ones in the signal spectrum. A filter is the piece of equipment that completes this purpose. The filter is an important radio frequency component of a wireless communication system. Image frequency interference is filtered out, noise is reduced, and frequency division multiplexing is used. Oscillation, amplification, frequency multiplication, and mixing circuits with excellent performance

An RF splitter is an electronic device that allows one RF input signal to be divided into multiple output signals with equal or unequal signal strength. The main purpose of an RF splitter is to distribute the input signal to multiple devices, such as TVs, radios, or other RF devices. RF splitters typically have a certain number of output ports, such as two-way, three-way, four-way, or more, depending on the number of devices that need to be connected. Each output port is designed to deliver the same signal strength as the input signal, but there may be some signal loss due to the division process.

An RF coupler is an electronic device that is used to couple or transfer radio frequency energy from one circuit or transmission line to another. RF couplers can be used to split or combine RF signals, provide signal isolation, and perform other functions in RF systems. RF couplers are widely used in various applications, such as wireless communications, radar systems, and satellite communication systems. When selecting an RF coupler, it is important to choose the right type and size of the coupler to match the frequency range and power levels of the RF signal.

Dummy loads are tools used to load down a device in order to do testing on amplifiers or RF systems. Some devices can be damaged if no load is used while testing. RF devices will always have to be tested with dummy loads attached. In RF, dummy loads are used to simulate a load of an antenna on a system without producing radio waves. They also use these for tuning the RF device before putting it online. They simulate a perfectly tuned antenna that is connected to the amplifier.

RF attenuators reduce the strength of an RF signal. Typically the RF signal is carried on a coaxial cable and an RF attenuator is used in line with that cable. They are also in circuit design and microwave applications. The need to reduce an RF signal may not immediately be obvious to the casual user who may have needed a signal amplifier for TV reception after struggling with a low signal. RF attenuators are essentially electrical resistors that are put in line with an RF signal and reduce the signal strength by converting some amount of RF energy into heat.

RF power combiners are passive RF/microwave components used for combining microwave signals. Mini-Circuits RF combiners include 2-way, 3-way, 4-way, 6-way, 8-way, and up to 48-way models for 50 Ohm and 75 Ohm systems, with DC-passing and DC-blocking, in coaxial, surface mount, and MMIC die formats. Our coaxial splitters are available with SMA, N-Type, F-Type, BNC, 2.92mm, and 2.4mm connectors. Choose from over 580 models in stock with frequency ranges up to 65 GHz, low insertion loss, high isolation, and excellent amplitude unbalance and phase unbalance.

An RF Duplexer is an electronic device used in RF communications transceiver circuits to allow sharing of the same antenna. This is important because transmitters are high-power large signal devices, and receivers are extremely sensitive small signal devices. Duplexers are available in different types. RF switches can alternatively connect, transmit, or receiver to the antenna in a time multiplexing arrangement.

An RF cable is a basic cable used primarily for carrying audio-visual signals. The name comes from an abbreviation of "radio frequencies." It is a type of Coaxial Cable, which involves a series of casings to protect the signal from interference. The coaxial design used in an RF cable is designed to prevent potential interference. To counteract this, the coaxial cable uses four circular layers. From the inside to the outside they are the wire carrying the signal; an insulating material which is usually solid plastic; a metal shield; and a plastic casing that protects the materials inside.

A low noise amplifier is used to amplify very low-power signals without significantly degrading their signal-to-noise ratio. They increase the amplitude of weak RF signals, which assists processing as part of a receiver circuit. The primary specification parameter of an LNA is its noise figure, which is a measure of how much the LNA degrades the signal-to-noise ratio of the received signal. Low noise amplifiers can also be used to compensate introduced loss in an RF signal path. By inserting a low noise amplifier, it will help to restore the original signal level, while ensuring the signal-to-noise ratio is retained.

RF repeaters have independent paths for reception and transmission, through which they collect and send signals to antennas and other stations. Radiofrequency (RF) repeaters, or RF repeaters, are communication devices designed to amplify or regenerate data signals in order to transfer telecommunication signals from one terminal to another. The purpose of an RF repeater is to amplify and reconstruct the signal so that it can be sent over a longer distance than would be possible without the repeater. RF repeaters are bidirectional amplifiers that, when located between two antennas, relay signals in remote locations, or in order to bypass obstructed paths.

A surge arrester is a protective device for limiting voltage on equipment by discharging or bypassing surge current. It prevents continued to flow to follow current to ground and can repeat these functions as specified per ANSI standard C62.11. An arrester does not absorb lightning or stop lightning. It diverts the lightning, limits the voltage, and protects the equipment installed in parallel. Surge arresters have many applications, anywhere from protecting a home to a utility substation. They are installed on circuit breakers inside a residential home, inside pad-mounted transformers, on pole-mounted transformers, on pole-mounted riser poles, and substations.